Pipe End Plugs, External & Internal, Fast, Efficient, For Sale Or Rent

Pipe End Plugs provide a fast and efficient method of installing temporary test caps on plain end pipe for hydrostatic leak and strength tests up to 350 bar / 5076 psi. Pipe End Plugs reduce time and material costs, minimise environmental impact and improve testing productivity and are robustly designed to sustain the rigours of the fabrication yard environment. STATS range of Pipe End Plugs cover two separate products with the I-PEP™ fitting the pipe internally and the patented E-PEP™ gripping the pipe externally.

E-PEP™ – External Pipe End Plugs

The E-PEP series of patented Pipe End Plugs are fitted to the pipe end and hydraulically actuated, gripping the pipe externally. The introduction of hydraulic set pressure activates a mechanical lock assembly that grips the outside diameter of the pipe whilst simultaneously energising an elastomeric seal in the internal diameter. This allows the pipework to be quickly and efficiently pressure tested with minimum preparation to the pipe end and no remedial work after the E-PEP is removed. A through-port allows the system to be filled and pressurised or vented through the E-PEP.

To remove the E-PEP from the pipe end, hydraulic pressure is applied to the unset circuit. Retracting the lock assembly and de-energising the seal, allowing the tool to be removed. The E-PEP range covers pipe sizes from 3” to 36” complementing the I-PEP range.

I-PEP™ – Internal Pipe End Plugs

The I-PEP series of Pipe End Plugs are inserted into the bore of the pipe and hydraulically actuated. These tools internally grip the pipe allowing hydrostatic pressure tests to be quickly and efficiently performed. The introduction of hydraulic set pressure activates a mechanical lock assembly that grips the internal diameter of the pipe whilst simultaneously energising an elastomeric seal. This allows the pipework to be quickly and efficiently pressure tested with minimum preparation required to the internal surface of the pipe and no remedial work after the I-PEP is removed. A through-port allows the system to be filled and pressurised or vented through the I-PEP. To remove the I-PEP from the pipe, hydraulic pressure is applied to the unset circuit, retracting the lock assembly and de-energising the seal allowing the tool to be removed.

Hydraulic I-PEPs cover pipe sizes from 30” to 42”, however for sizes ¾” to 2” mechanical tools are used and fitted with securing clamps for added safety.

All Pipe End Plugs are designed in accordance with STATS engineering standards (based on international codes) to facilitate testing in accordance with ASME B31.3 and similar piping codes. Sizes are based on standard pipe with interchangeable seals to cover ASME B36.10 and ASME B36.19 schedules.

Specification

Size

¾" - 42"

Pressure

350 bar / 5076 psi

Activation

Hydraulic above 2”

Operator Benefits

Reduced cost associated with welding and cutting end caps
Saves time with faster completion of hydrostatic testing

Sale or rental options available, complete with full ancillary equipment

Key features

Simple, straight forward installation, installed and activated in a matter of minutes
Test pressure applies differential pressure across the tool, keeping the locks and seals self-energised ensuring fail-safe operation
Generous radial clearance to cope with typical internal obstructions such as weld beads, ovality, etc.
Non-destructive, does not damage the interior/exterior wall of pipes or vessels

High performance, large section, quality elastomer seals ensure a leak-tight seal and provide excellent radial expansion and relaxation properties, even after many operating cycles
Through-port allows efficient fill or vent of the test medium
Suitable for installation in horizontal, vertical and inclined piping
Internal/external grip lock assembly applies even, linear and circumferential grip load around the host pipe, eliminating localised material deformity and localised stress fractures

Related Resources

Hydrostatic Test | Pipe End Plugs | E-PEP™

Play Video

Pipe End Plugs facilitate Pipe Spooling for Aasta Hansteen Field

Subsea 7 contracted STATS Group to provide positive isolation of pressurised mechanically lined BuBi® pipe to facilitate reeling onto a pipe lay vessel at their facility ...

Read the Case Study

Terms & Conditions

Click on the links below to download a copy of our Terms and Conditions

Purchase Order Terms and Conditions

Terms and Conditions for Sale, Rental, and Services

For further information, please email: sales@statsgroup.com

Pipe End Plugs